Hoppa till innehåll
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Detecting Moisture in Wood and Walls Before the Damage Becomes VisibleWhy the Cold Chain Usually Breaks at Night, and Only a Data Logger Shows ItGhost Voltage and Variable Frequency Drives: Why Many Measurements on Drives Are WrongMeasuring Busbars and Cable Bundles When a Rigid Clamp Jaw No Longer FitsWhen the Shock Really Happened: How a 3-Axis Data Logger Provides Evidence of Transport Damage and VibrationMeasuring Speed Without Contact: How a Stroboscope Makes Rotating Parts Appear to Stand StillWhy an Infrared Thermometer with 50:1 Optics Still Measures the Right Spot at Five Metres‘ DistanceSeamless Documentation of Dew Point and Humidity: Why a Data Logger Shows More Than Any Spot CheckWhy Your Multimeter Shows 230 Volts Even Though the Line Was Switched Off Long AgoMeasuring Temperature and Proving It at the Same Time: Why the Photo Belongs with the ReadingVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Detecting Moisture in Wood and Walls Before the Damage Becomes VisibleWhy the Cold Chain Usually Breaks at Night, and Only a Data Logger Shows ItGhost Voltage and Variable Frequency Drives: Why Many Measurements on Drives Are WrongMeasuring Busbars and Cable Bundles When a Rigid Clamp Jaw No Longer FitsWhen the Shock Really Happened: How a 3-Axis Data Logger Provides Evidence of Transport Damage and VibrationMeasuring Speed Without Contact: How a Stroboscope Makes Rotating Parts Appear to Stand StillWhy an Infrared Thermometer with 50:1 Optics Still Measures the Right Spot at Five Metres‘ DistanceSeamless Documentation of Dew Point and Humidity: Why a Data Logger Shows More Than Any Spot CheckWhy Your Multimeter Shows 230 Volts Even Though the Line Was Switched Off Long AgoMeasuring Temperature and Proving It at the Same Time: Why the Photo Belongs with the Reading

Why a Loose Terminal Connection Often Goes Unnoticed Until You Measure Current and Temperature at the Same Time

Published on October 13, 2026 at 9:17 a.m.

A control cabinet has been running without any problems for months, then a motor protection switch trips. The voltage was fine, and so was the current in a quick follow-up measurement. The cause is only found later: a terminal that ran too hot over a long period and built up resistance as a result. Anyone working in maintenance or production knows this situation, where a single measured value is not enough.

1000A True-RMS AC / DC Clamp Meter with IR Thermometer

What the Device Is

The 1000A True-RMS AC/DC Clamp Meter is a clamp meter that also works as a multimeter. It measures AC and DC current as well as voltage, resistance, capacitance, frequency, continuity and diodes. It also features a Type K input and a non-contact infrared thermometer with a laser pointer. The 43 mm jaw opening accommodates conductors up to 750 MCM, or alternatively two conductors of 500 MCM each.

Which Problems It Solves

True-RMS measurement matters most where the load is not sinusoidal, for example downstream of frequency converters or on switched-mode power supplies. Simple devices often display values that are too low in these cases. The peak-hold mode captures inrush currents and brief transients that occur when a motor starts and cannot be read off the display with the naked eye. The infrared thermometer provides the second piece of information: it shows whether a conductor, a terminal or a bearing housing heats up abnormally during operation, without the need to touch the component.

When It Is Used

A typical use is measuring under load when the system cannot be switched off. The clamp encloses the conductor without interrupting the circuit. After that, a glance with the laser pointer at the connection point is enough. With the data-hold function and the min/max memory, values can be saved even at hard-to-reach locations and read off afterwards at leisure.

Three Practical Applications

Workshop and mechanical engineering: When a milling machine or a compressor starts up, the inrush current is recorded and compared with the nameplate. If it deviates significantly, this points to bearing damage or a supply line that is too weak.

Electrical distribution and building services: During regular inspections of distribution boards, the current draw per feeder and the temperature of the terminal points are checked in one pass. A connection that is clearly warmer than its neighbors is retightened before it fails.

Food production: On conveyor belts, agitators and refrigeration units, current draw can be monitored. If it slowly rises under constant load, mechanical wear is usually on the way. The motor’s surface temperature provides the matching confirmation.

Why the Purchase Pays Off

In many cases, one device replaces three measuring tools: clamp, multimeter and infrared thermometer. This saves walking distances, changeover time and purchase costs. The greater effect lies elsewhere. A terminal that is identified as too warm in time costs one minute of maintenance, whereas an unplanned machine stoppage costs lost production and troubleshooting. A single avoided failure per year generally more than covers the price of the device.

Conclusion

Anyone who wants to assess current and temperature in the same work step gets both values from a single source with this clamp meter, while the system is running and without intervening in the circuit. You will find details on features and scope of delivery on the product page.

Learn more

More news

All news