Published on July 11, 2026 at 1:16 AM
An HVAC technician has to balance an office ventilation system. Six rooms, six air outlets, six different air volumes according to the design plan. They need to verify that each room actually receives its specified air volume. Under EN 16798-3, the actual values should be within ±15% of the design values. Otherwise the air conditioning system won’t perform as planned, and rooms will be either under- or over-supplied.
They could measure with a vane anemometer, but the outlet sits at a ceiling panel 3.5 m up, and the vane is 100 mm in diameter. The outlet opening is only 60 mm wide, so it won’t fit. What they really need is an instrument with a thin probe that fits through the 60 mm opening and still measures air velocity accurately. That instrument is the hot-wire anemometer, and the SDL350-NIST is one, with a 215 cm telescopic probe.
King’s Law: The Physics Behind the Hot Wire
Hot-wire anemometry was described analytically in 1914 by the British physicist Louis Vessot King (1869-1957). His principle:
- A very thin metal wire (typically 5 μm tungsten or 50 μm platinum) is heated by an electric current to a temperature above that of the ambient air, usually 100-300 °C above ambient.
- When air flows past the wire, it cools the wire by forced convection.
- The cooling power P (watts) required to keep the wire at a constant temperature depends on the flow velocity v.
King’s mathematical law is:
P = A + B × vn
Where:
- P = heat loss from the wire (the electrical power needed to hold the temperature constant).
- A = heat loss through natural convection and radiation (at v = 0).
- B = a constant that depends on wire diameter, wire length and air properties.
- v = flow velocity (m/s).
- n = King’s exponent, ~0.5 for most conditions.
Practical consequence: if the instrument measures the electrical power P needed to maintain the temperature, it can calculate v using the inverse of King’s equation. The wire is held at a constant temperature by a control loop (CTA mode, Constant Temperature Anemometry).
Why Hot Wire Instead of a Vane?
There are three main anemometer technologies for HVAC work:
Vane anemometers: A small wind wheel that rotates with the flow. Advantages: very simple, robust, no calibration needed. Disadvantages: mechanical inertia (below 0.5 m/s the wheel won’t start), a wheel diameter of 40-100 mm (doesn’t fit into small ducts), and directional dependence (it measures only the component along the wheel axis).
Pitot-static (Prandtl) tube: The classic aerodynamic solution. Advantages: high accuracy at high velocities, no electronics needed. Disadvantages: a probe diameter of several mm, not sensitive below 2 m/s, and a reference manometer is required.
Hot-wire anemometers: Advantages: a very small probe (typically 2-5 mm in diameter), sensitivity down to 0.1 m/s, no mechanical inertia (instant response), and accurate even at low flows. Disadvantages: requires calibration, is sensitive to dust contamination, and the probe can be destroyed by foreign objects.
For HVAC balancing (typical velocities of 0.5-5 m/s in ventilation ducts, 0.1-1 m/s in rooms), the hot wire is the right choice. It measures accurately across the entire range and fits into almost all outlet openings.
The Telescopic Probe: More Than Convenience
The SDL350-NIST has a telescopic probe with a maximum extended length of 215 cm. Why so long?
HVAC ducts are typically 200-500 mm in diameter and run 2-4 m high along ceilings. The technician needs to measure air velocity at the DUCT AXIS (not at the edge), because flow at the edge is reduced by wall friction. With a 400 mm duct height and the outlet at a ceiling height of 3.5 m, the probe tip has to reach about 200 mm INTO the duct interior and then up to the 3.5 m ceiling height. That requires a reach of 3.7 m from the cable end.
The telescopic probe is typically:
- A 5-segment aluminum telescope.
- Collapsed: 30-40 cm.
- Extended: 215 cm.
- Probe tip with hot-wire sensor and temperature sensor.
- Cable from the instrument to the probe handle: 1-1.5 m.
- Total reach: 3.15-3.65 m, just right for a ceiling outlet at a height of 3.5 m.
Simultaneous Temperature Measurement
The SDL350 measures not only air velocity but also air temperature at the same time. Why does that matter?
1. Volume flow calculation: The volume flow V (m³/s) is calculated from air velocity v (m/s) and duct cross-section A (m²) as V = v × A. However, the MASS flow ṁ (kg/s) depends on the air density ρ, and ρ in turn depends on temperature and pressure. For accurate mass flow measurements, a temperature correction becomes necessary.
2. King’s law correction: The constants A and B in King’s equation are themselves temperature-dependent. Without a temperature reference, the velocity measurement drifts. Internal temperature compensation is standard in high-quality hot-wire anemometers.
3. Delta-T measurements: In HVAC diagnostics, the temperature difference between supply air and return air is often the key diagnostic quantity. A 2°C deviation from the design value can already be a symptom of a compressor problem.
The SDL350 shows both values simultaneously on the LCD display, and an additional Type K/J thermocouple input allows a second, independent temperature measurement, for example measuring the duct interior temperature and the room temperature at the same time.
SD Card for Long Recordings
The SDL350 stores up to 20 million readings on an SD card in an Excel-compatible format. This is important for:
- 24-hour balancing: Some occupancy situations change over the course of the day. A 24-hour recording shows whether the air conditioning system still delivers the specified volume flows at full occupancy.
- Control behavior analysis: Modulating systems (VAV, variable air volume) are supposed to change volume flows when room demand changes. Data logging shows whether the control behavior actually works.
- Filter change verification: Measure before and after a filter change. Clogged filters show a markedly reduced volume flow at the same system output.
- Commissioning documentation: Electronic records are typically mandatory for technical documentation under VDI 6032.
Configurable sampling rate: from 1 s to 60 min per reading. At 1-minute sampling, 20 million readings equal 38 years of continuous recording. In practice, SD card storage capacity is never the limiting factor.
NIST Calibration Certificate
The NIST version of the instrument comes with a traceable calibration certificate from the US national metrology institute. This is important for:
- Commercial HVAC balancing: Many tender contracts require a NIST certificate.
- ISO 9001-certified facilities: All test equipment must be calibrated with traceability.
- Court-admissible measurements: In disputes over non-compliance with HVAC specifications.
- Hospitals and sterile laboratories: Where the indoor climate directly affects patient or product safety.
Recommended recalibration: annually. Cost at an accredited laboratory: 300-800 EUR.
Areas of Application
HVAC technicians: Balancing ventilation systems after installation. The standard workflow.
Building inspectors: Verifying that the ventilation system actually delivers the design values.
Cleanroom technicians: Class 100/1000/10000 cleanrooms require specific airflows and turbulence levels. The hot-wire anemometer is the standard verification instrument.
Kitchen exhaust technicians: Restaurant kitchens need defined exhaust volumes for fire protection and smoke management.
Hospital facilities: Operating rooms, intensive care units and isolation rooms have strict airflow requirements.
Testing laboratories: Aerodynamic test stands, wind tunnels for material testing, filter testing.
Safety engineers: Verifying smoke extraction in fire protection systems.
Industrial ventilation: Chip extraction, welding fume extraction, chemical vapor extraction.
Agricultural barns: Animal health depends on adequate ventilation.
Cleanroom certification: The semiconductor and pharmaceutical industries with ISO 14644 requirements.
Limitations of the Instrument
- Dust contamination: The hot wire is delicate. In very dusty environments (construction sites, grinders, mills), the service life of the probe is significantly shortened.
- Moisture condensation: When measuring in very humid air or air prone to condensation, water can collect on the wire and distort the measurement.
- Very high velocities (above 25 m/s): Hot-wire sensitivity drops off at very high flows. For wind tunnel measurements above 30 m/s, Pitot-static (Prandtl) tubes are better.
- Turbulence level measurement: The SDL350 measures mean velocity, not turbulence intensity. Turbulence measurements require higher-grade anemometers with kHz sampling.
- Directional sensitivity: The probe measures only the velocity component perpendicular to the wire. In highly swirling flow, the measurement result can be misleading.
What You Get for Your Money
Extech SDL350-NIST hot-wire thermo-anemometer with datalogger, telescopic probe extendable to 215 cm, simultaneous measurement of air velocity and temperature, additional input for Type K/J thermocouple, 9999-count LCD display, SD card slot for 20 million readings in Excel format, configurable sampling rate from 1 s to 60 min, MIN/MAX/DATA HOLD functions, PC interface, powered by 6 x AA batteries, supplied with SD card + telescopic probe + hard case, traceable NIST calibration certificate. 1,100 EUR.
A standard instrument for professional HVAC balancing, cleanroom verification and other applications where precise air velocity measurement with a thin probe is needed in ducts up to 5 m deep. The combination of hot-wire technology, telescopic probe and NIST traceability makes it an investment that pays off quickly for building inspectors, HVAC technicians and cleanroom engineers.
Read more: Extech SDL350-NIST Hot-Wire Anemometer in the Shop →