Hoppa till innehåll
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Ghost Voltage and Variable Frequency Drives: Why Many Measurements on Drives Are WrongMeasuring Busbars and Cable Bundles When a Rigid Clamp Jaw No Longer FitsWhen the Shock Really Happened: How a 3-Axis Data Logger Provides Evidence of Transport Damage and VibrationMeasuring Speed Without Contact: How a Stroboscope Makes Rotating Parts Appear to Stand StillWhy an Infrared Thermometer with 50:1 Optics Still Measures the Right Spot at Five Metres‘ DistanceSeamless Documentation of Dew Point and Humidity: Why a Data Logger Shows More Than Any Spot CheckWhy Your Multimeter Shows 230 Volts Even Though the Line Was Switched Off Long AgoMeasuring Temperature and Proving It at the Same Time: Why the Photo Belongs with the ReadingNon-Destructive Coating Thickness Testing: What the Paint Layer Reveals About Coating Quality and Accident DamageA 5.8 mm camera shows what lies behind the casing, without taking the machine apartVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Ghost Voltage and Variable Frequency Drives: Why Many Measurements on Drives Are WrongMeasuring Busbars and Cable Bundles When a Rigid Clamp Jaw No Longer FitsWhen the Shock Really Happened: How a 3-Axis Data Logger Provides Evidence of Transport Damage and VibrationMeasuring Speed Without Contact: How a Stroboscope Makes Rotating Parts Appear to Stand StillWhy an Infrared Thermometer with 50:1 Optics Still Measures the Right Spot at Five Metres‘ DistanceSeamless Documentation of Dew Point and Humidity: Why a Data Logger Shows More Than Any Spot CheckWhy Your Multimeter Shows 230 Volts Even Though the Line Was Switched Off Long AgoMeasuring Temperature and Proving It at the Same Time: Why the Photo Belongs with the ReadingNon-Destructive Coating Thickness Testing: What the Paint Layer Reveals About Coating Quality and Accident DamageA 5.8 mm camera shows what lies behind the casing, without taking the machine apart

Non-Destructive Coating Thickness Testing: What the Paint Layer Reveals About Coating Quality and Accident Damage

Published on November 11, 2026 at 2:14 pm

A component comes out of the galvanizing plant, looks even and goes out for shipping. Three months later, the customer reports rust on the edges. Or a used car gleams flawlessly, but the driver’s door was repainted after an accident without anyone documenting it. In both cases, coating thickness is the deciding factor, and the eye alone tells you nothing about it.

Coating thickness tester

One device for two substrates

The Extech CG104 coating thickness tester measures coating thickness non-destructively and with one hand. It works with two methods. On ferrous substrates such as iron and steel, it uses magnetic induction. On non-ferrous metals such as copper, aluminum, zinc, bronze or brass, it uses eddy current. The device detects the substrate by itself. You do not have to select the operating mode and cannot accidentally measure with the wrong method.

Which problems it solves

Without a measuring instrument, all that remains is scratching the coating or cutting a cross-section from a sample. Both damage the part and cannot be repeated at every location. The CG104 checks the finished part at as many points as you like. A high and a low limit trigger an audible alarm, so you notice deviations immediately. The display can be rotated by 180°, so you can read the value even in places where you have to hold the device at an awkward angle. Auto-Hold freezes the measured value, and the minimum, maximum and average values can be recalled.

When and how it is used

Before the first measurement, a zero adjustment is performed on the uncoated substrate, with a two-point calibration if needed. The required calibration plates (ferrous, non-ferrous and a paint film as a standard) are included in the delivery. After that, you place the probe on the surface, read the value and store up to 255 measurements for documentation.

Three typical applications

Quality assurance in surface treatment: For galvanizing or anodizing, you check whether the target coating thickness has been met before the batch is delivered. The measurement series with its average value serves as proof for the customer.

Paint shops and corrosion protection: Between work steps, painters and inspectors check whether primer and topcoat reach the required thickness. Too little coating does not protect sufficiently, while too much costs material and is prone to cracking.

Vehicle assessment: Significantly elevated values on individual body parts indicate repainting. This helps when buying a used car and when assessing previous accident repairs.

Why the investment pays off

The benefit lies in what you avoid. A complaint about a coating that is too thin causes returns, rework and loss of trust, and a coating that is too thick wastes material on every part. Because the test is non-destructive, the part remains saleable. The device stays compact, needs only two AAA batteries and fits into any tool bag with its wrist strap and soft case. Even a single avoided rework or misjudgment often covers a good part of the cost.

If you no longer want to judge coatings by eye, you will find the technical details and the package contents on the product page.

Learn more

More news

All news