Hoppa till innehåll
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Detecting Moisture in Wood and Walls Before the Damage Becomes VisibleWhy the Cold Chain Usually Breaks at Night, and Only a Data Logger Shows ItGhost Voltage and Variable Frequency Drives: Why Many Measurements on Drives Are WrongMeasuring Busbars and Cable Bundles When a Rigid Clamp Jaw No Longer FitsWhen the Shock Really Happened: How a 3-Axis Data Logger Provides Evidence of Transport Damage and VibrationMeasuring Speed Without Contact: How a Stroboscope Makes Rotating Parts Appear to Stand StillWhy an Infrared Thermometer with 50:1 Optics Still Measures the Right Spot at Five Metres‘ DistanceSeamless Documentation of Dew Point and Humidity: Why a Data Logger Shows More Than Any Spot CheckWhy Your Multimeter Shows 230 Volts Even Though the Line Was Switched Off Long AgoMeasuring Temperature and Proving It at the Same Time: Why the Photo Belongs with the ReadingVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Detecting Moisture in Wood and Walls Before the Damage Becomes VisibleWhy the Cold Chain Usually Breaks at Night, and Only a Data Logger Shows ItGhost Voltage and Variable Frequency Drives: Why Many Measurements on Drives Are WrongMeasuring Busbars and Cable Bundles When a Rigid Clamp Jaw No Longer FitsWhen the Shock Really Happened: How a 3-Axis Data Logger Provides Evidence of Transport Damage and VibrationMeasuring Speed Without Contact: How a Stroboscope Makes Rotating Parts Appear to Stand StillWhy an Infrared Thermometer with 50:1 Optics Still Measures the Right Spot at Five Metres‘ DistanceSeamless Documentation of Dew Point and Humidity: Why a Data Logger Shows More Than Any Spot CheckWhy Your Multimeter Shows 230 Volts Even Though the Line Was Switched Off Long AgoMeasuring Temperature and Proving It at the Same Time: Why the Photo Belongs with the Reading

Extech UM200 Micro-Ohm Meter with Kelvin 4-Wire Measurement: Why a 5 Milliohm Contact Resistance Turns a 200 A Busbar Connector into a Fire Risk

Published on July 7, 2026 at 3:30 PM

Measuring resistance in the milliohm and micro-ohm range is one of the specialized disciplines of electrical measurement technology. It sounds simple — it is „just“ a very small resistance — but the physics of the measurement method changes fundamentally as soon as the resistance being measured is comparable to or smaller than the resistance of the test leads. It is precisely in this range, where standard multimeters fail, that critical operational safety questions are decided: the contact resistance of a screw connector, the quality of a spot weld, the winding resistance of a motor, the contact resistances in grounding systems.

What the Extech UM200 Is

High Resolution Micro-Ohm Meter (53-UM200) from Extech is a portable precision micro-ohm meter using the Kelvin 4-wire measurement method. The instrument:

  • Measures resistances from a few micro-ohms up to the ohm range.
  • Uses true 4-wire Kelvin measurement with separate current and voltage leads.
  • Supplies a test current of up to 10 A so that the voltage response can be measured even at the smallest resistances.
  • Offers 6 ranges, each with 3 sub-ranges for optimal resolution.
  • Measures both resistive and inductive materials (motor windings).
  • Has a 5-digit LCD display.
  • Automatic and manual range selection.
  • Memory function for up to 3000 readings.
  • Cable length measurement function (feet or meters).
  • PC interface for data download.
  • Rechargeable Li-polymer battery (for cordless field use).
  • Includes 4 Kelvin clip leads for measurements.

Basic specifications:

  • Measurement method: 4-wire Kelvin
  • Test current (maximum): 10 A
  • Number of ranges: 6 main ranges with 3 sub-ranges each
  • Display: 5-digit LCD
  • Memory: 3000 readings
  • PC interface: USB
  • Range selection: Automatic / manual
  • Additional function: Cable length measurement
  • Application: Resistive + inductive materials
  • Power supply: Li-polymer battery + AC adapter
  • Includes: 4 Kelvin clip leads, charger, USB cable, software, carrying case

Extech UM200 Mikro-Ohm-Meter mit Kelvin-4-Leiter-Messung

Why 4-Wire Kelvin Measurement Is Necessary

The fundamental problem with 2-wire resistance measurement: the test leads are part of both the current path AND the voltage measurement. The measured ohms are therefore made up of:

R_measured = R_DUT + 2 × R_lead + 2 × R_contact

Typical values:

  • R_lead (1 m test cable, 0.5 mm²): 0.03-0.05 ohms
  • R_contact (spring contact against oxidized metal): 0.01-0.10 ohms
  • Combined: 0.08-0.30 ohms of parasitic resistance

For a device under test of 10 ohms, that is a 1-3% error — acceptable. For a device under test of 10 milliohms, that is an 800-3000% error — the measurement is worthless.

The Kelvin 4-wire principle solves this geometrically:

  1. Two separate pairs of leads on the device under test — one pair for current injection, one pair for voltage measurement.
  2. The voltage leads carry practically no current (only the bias current of the voltmeter input, a few microamperes).
  3. No voltage drop across the voltage leads → their resistance has no influence on the measurement.
  4. The current leads are irrelevant to the measurement — they only deliver the defined test current.

Result: the measured resistance is precisely that between the voltage sensing points. The test lead resistance drops out of the calculation entirely.

Kelvin Clips (4-Jaw) in Detail

Kelvin clips have two electrically isolated pairs of jaws that grip the same component:

  • Inner jaws: voltage sensing.
  • Outer jaws: current injection.

The jaws are electrically separated by an insulating piece (typically 1-2 mm apart). Both pairs contact the same surface of the device under test, so that current injection and voltage sensing occur at nearly identical points geometrically — which is essential for accuracy.

10 A Test Current — Why So High

At the smallest resistances, Ohm’s law yields very small voltage responses:

  • 10 mA × 1 mΩ = 10 μV (hard to measure, deep in the noise)
  • 1 A × 1 mΩ = 1 mV (readily measurable)
  • 10 A × 1 mΩ = 10 mV (clearly above the noise, high resolution possible)

This is why precision micro-ohm meters typically inject 1-10 A. The high test current has two side effects that need to be planned for:

  • Heat generation: At 10 mΩ with 10 A: P = I²R = 1 W. Uncritical when measured over a few seconds, but during longer measurements the device under test can heat up (resistance rises).
  • Thermoelectric effects: At junctions of dissimilar metals (e.g. a copper clamp on a steel bolt), small thermal voltages (~40 μV/°C) arise. In micro-ohm measurement these become visible. Modern micro-ohm meters compensate by alternating the current direction (pulse +/−).

Application Example: Busbar Joint Testing

An industrial 200 A busbar joint is ideally a copper-to-copper contact with screw pressure. Expected contact resistance: 0.02-0.05 mΩ. After several years of operation, it rises due to oxidation and mechanical loosening. Critical limit: above 0.2-0.5 mΩ, there is a risk of heat generation.

Heat calculation at 200 A operation:

  • 0.05 mΩ (new): P = 200² × 0.00005 = 2 W. Uncritical.
  • 0.5 mΩ (worn): P = 200² × 0.0005 = 20 W. The joint becomes noticeably warm.
  • 5 mΩ (failure): P = 200² × 0.005 = 200 W. Fire hazard, melting.

Regular micro-ohm inspection detects the critical wear stage BEFORE failure.

Where Micro-Ohm Measurement Makes a Real Difference

Switchgear and distribution panels: Contact resistance of disconnect switches, busbar connections, fuse holders.

Transformers: Winding resistance (copper losses), tap changer contact resistance.

Motors and generators: Winding resistance across the three phases should be balanced (±2% max).

Cable connections: Crimp sleeves, cable lugs, bolted terminals.

Grounding systems: Grounding resistances of lightning protection systems, facility grounding.

Spot welds and resistance welds: QC testing of weld quality through resistance measurement.

Battery systems: Cell connections in traction batteries, UPS systems, PV storage.

Printed circuit board testing: Copper trace resistances, plated-through holes (vias).

Photovoltaic systems: Module terminal contacts, inverter connections.

Rail and industrial drives: Traction motor windings, braking resistors.

Chemical plants: Electrolysis cell connections, cathodic protection systems.

Measurement Methodology in Practice

  1. De-energize and discharge the device under test: Absolutely critical for inductive test objects (motors, transformers) — stored energy can destroy the instrument.
  2. Remove oxide layers: At the measurement points with a file or brush, so that the contact is low-resistance.
  3. Connect the Kelvin clips: The inner and outer jaws must make secure contact. Do not clamp onto paint, rust or insulation.
  4. Range selection: Use auto-ranging or select the appropriate manual range.
  5. Start the test current: The instrument automatically delivers the defined current.
  6. Document the reading: In the maintenance log with date, measurement point, temperature.
  7. Trend tracking: Comparison with previous readings shows wear progression.
  8. After measurement: Disconnect the cables, discharge the instrument.

What You Get for Your Money

Extech UM200 high resolution micro-ohm meter, 4-wire Kelvin measurement method, up to 10 A test current, 6 measurement ranges with 3 sub-ranges each, 5-digit LCD display, automatic and manual range selection, memory for 3000 readings, PC interface (USB) with software for data download, measurement of resistive and inductive materials (motor windings), cable length measurement function (feet / meters), rechargeable Li-polymer battery for cordless field use, AC adapter/charger, 4 Kelvin clip leads, carrying case.

2,767 EUR is the instrument investment. Compared with high-end laboratory precision micro-ohm meters (5,000-25,000 EUR), the UM200 is a portable field solution for maintenance teams, electrical installation inspectors and maintenance technicians. The return on investment is clear: a single prevented fire-damage repair on a 400 A distribution system pays for the instrument many times over.

Learn more: Extech UM200 Micro-Ohm Meter in the Shop →

More news

All news